Urgent Care Re-post: How To Straighten A Guitar Neck With An Adjustable Truss Rod

Home » Haywire Custom Guitars Blog of Guitar Tips » Urgent Care Re-post: How To Straighten A Guitar Neck With An Adjustable Truss Rod

Urgent Care Re-post: How To Straighten A Guitar Neck With An Adjustable Truss Rod

Updated on Feb. 14, 2012

Angled Head-stock style of adjustable truss rod

image results for Angled Headstock style of adjustable truss rod
Angled Headstock style of adjustable truss rod

The neck of your guitar is adjustable

In most cases, the of a guitar neck is adjustable. Although the wood is generally hard, dry and stiff it will still bend with string pressure and humidity or lack thereof. In our shop we have to deal with that issue on a daily basis. Inside the neck is a routed channel between the finger board and the neck shaft where a truss rod is placed to compensate for movement on the forward axis of the neck to add stability. The rod is steel and is adjustable. It runs the length of the guitar neck with an opening at one end allowing for adjustments.

adjustment called “relief” in the neck

The truss rod both strengthens the neck and facilitates an adjustment called “relief” in the neck. A bowed or humped neck can be reversed with skillful manipulation by the adjuster-you. All guitar necks are subject to great stress. This is sometimes the result of seasonal change, Other times when a neck could take on a slight bow or hump are from string changes with gauges higher than normally used. A guitar player will usually know a little about how to make some adjustments on his guitar. Some things however may contribute to a misaligned neck.

Several of the “usual problems” seen are heavier gauge strings which increases the forward pressure, removing all of the strings at once and leaving guitars in a hot car. These actions will cause immediate negative pull and the will revert naturally back to where it started. However, if it does, there is a solution if you follow the procedure below for proper re-positioning of a bowed neck. In our Custom shop this is the procedure we use.

neck could take on a slight bow or hump are from string changes

 

First, loosen all the strings but you will not have to remove them. Push the loose strings to one side to gain access to neck adjuster. Remove cover, so neck adjuster is exposed. It’s either an Allen screw or a hex nut. Look down the neck from the top where the tuners are located towards the bridge (similar to sighting a down the barrel of a gun) to see how much of a bow or hump the neck has in it.

It is recommended to use a Notched Straightedge to see how far out of alignment the neck really is. The notches are on both side of the tool. One side has cutouts for a 24-3/4″ scale neck and the other is for the most common 25-1/2″ scale. They are there so frets can be avoided when the tool comes in contact with the fret board. The frets fit neatly in the cut out and the straight edge will show any problems when it lies straight on the fret board.

the guitar neck is out of adjustment

At this point, if it is discovered that the guitar neck is out of adjustment, it’s time to go to work. Insert the Allen key or hex wrench in the Allen slot or on the adjustment nut. Turn very gently in small increments at a time. Checking the neck as you proceed with each nut turn is required. Once the guitar neck is straight keep adjusting a bit more to compensate for the tension the stings will add once they are re-tuned to pitch. Turn right or clockwise for ” BOW ” alternately left or counterclockwise for a HUMP. Take special care as not to tighten the nut too much because it could result in a broken truss rod, stripped threads and a much larger monetary outlay than originally intended.

too much “guitar string buzz”

This should fix the problem! There seems to be an inordinate amount of “string buzz”. If you find this impossible to live with bring it in to your guitar tech for further inspection. If the guitar neck has a “twist” it can void the neck straightening process you have just used and will need attention from a Luthier.

On some “Vintage Guitars” the guitar neck truss rod adjustment is the same but in a different location. It is made at the end of the fingerboard called the guitar Heel or Butt end.

Haywire Custom Guitars “Violator”

Ordering From Haywire Custom Guitars

If you would like to order this or any other custom guitar, please contact us and we will be happy to discuss your guitar needs.

About the Author:

Mr. Rick Mariner Owner and Founder and CEO of Haywire Custom Guitars Inc. He is a member of The Association of Stringed Instrument Artisans (A.S.I.A.) as well as a guitar player. Rick holds a bachelors degree from University of Md.and a Masters degree from George Washington University. Rick developed his exclusive 8 – Point “Gig- Ready” guitar process that allows for Custom Guitars that are “GIG-READY”. With Rick’s many years of development and guitar set-up experience, Haywire Guitar shop “Builds satisfied players… one Haywire guitar at a time”.

Leave A Comment