Call Us Today! 843-347-5742|haywire@sccoast.net

Installing A Bolt-On Guitar Neck

Special Re-print

image Haywire Custom Guitars Nashville SG -2

 Installing A Bolt-On Guitar Neck

    at: Haywire Custom Guitars Inc.

  Haywire Custom Guitars Inc.

If a bolt-on neck will drop in a body with a bit of room to align it right or left that’s a good start so far. Generally when I prep a neck I’ll fill any existing screw holes in the heel. If there are holes already drilled in the neck heel, you can try to use them, but honestly never trust holes on necks drilled by someone else.  It’s always best for the most successful project to drill your own holes in the neck heel (and have a depth stop on the drill bit so you don’t drill through the fret board on other side)…. blue tape works well. When ordering a “New” neck I recommend omitting the mounting holes and drilling them yourself to match your body.

The optimum way to begin, with the least headaches, is to simply dowel the existing holes. Use wooden Bar-B-Que skewers then add glue in the hole break them off in the holes, sand smooth and you ready to go. Now with a fresh clean surface to work with you can move to the next step.

So let’s go over how to get this operation PERFECT.  I have used this method in hundreds of neck installs and it is the best technique. As follows and note: You’ll need to add both ” the 1st & 6th E” strings to the neck before final installation on body to set the string margins exactly.

Let’s start……….

First: Tape the neck plate onto the back of the body vertically and horizontally leaving the holes exposed. Next, using a “C” clamp, add the bolt-on neck, body and neck plate together and place a thin piece of wood in each jaw to protect the guitar fret board then tighten. Snug it but not too tight. Now, add the two outside “E” strings. This is where a very slight gap between the sides of the neck and body comes in handy and extremely helpful.

Setting the margins is a critical operation, however not difficult

Setting the margins is a critical operation, however not difficult.  Once you have clamped the neck and added the 2 outside strings, face the guitar. Now, In addition, move the neck right or left to get the string margins set perfect on each side of the fret board all the way down.

Once this is done then you can enter the next installation steps. Finally, take care to “mark the screw hole depth” on the drill bit with tape.  As a result, you won’t  to drill through the front of the fret board.  Ready?  Tighten the clamp, spin the guitar around and drill one hole. Add the first screw (some liquid dish detergent always helps the journey for the screw threads to enter smoothly). Now spin the guitar back around to check your string margins again.  Be sure the neck hole alignment is good through the back plate. If the neck needs adjustment then tap hard on the head stock with the heel of your hand.

This will get everything aligned again. Now you’re ready for the rest of the holes to be drilled in the bolt-on neck.

margin space between the outside strings and the edges of the fret board…

Installing  a bolt-on neck is not a difficult process but methodical and deliberate. Most noteworthy, follow this on EVERY neck install.  Your necks will all come out with the perfect amount of margin space.  The space between the outside strings and the edges of the fret board. Once in the neck may need shims to tilt it either up or back. Be sure and add shims if necessary. They are sometimes critical to eliminating “Buzz”.

This technique will assure that everything is straight and true. A small gap will help to accomplish this. It will give you enough room to set the margins exactly right on each side.  Let me know if I can assist further. Also please write us from the Haywire Custom Guitars website and let us know what you’re interested in.

Ordering From Haywire Custom Guitars

If you would like to order this or any other custom guitar, please contact us and we will be happy to discuss your guitar needs.

Rick Mariner-Haywire Custom Guitar Shop

Haywire Custom Guitars-Recessed Heel Crest Option before and after photo

Bolt-on guitar neck

About the Author:

Mr. Rick Mariner Owner and Founder and CEO of Haywire Custom Guitars Inc. He is a member of The Association of Stringed Instrument Artisans (A.S.I.A.) as well as a guitar player. Rick holds a bachelors degree from University of Md. and a Masters degree from George Washington University. Rick developed his exclusive 8 – Point “Gig- Ready” guitar process that allows for Custom Guitars that are “GIG-READY”. With Rick’s many years of development and guitar set-up experience, Haywire Guitar shop “Builds satisfied players… one Haywire guitar at a time”.

Leave A Comment